Site Information

 Loading... Please wait...

Meyer Sound 700-HP Active Subwoofer

$3,489.00

Other Details

Location:
North America & Europe
Warranty:
Limited warranty
Sales Questions?:
Condition:
Used

MEYER SOUND 700-HP SUBWOOFER (pre-owned)

Meyer’s 700-HP has almost twice the performance power of the popular Meyer Sound 650-P subwoofer, and the 700-HP subwoofer has become a standard across the industry. The 700iHP delivers a high and sustained level of work with extremely high impulse response and minimal distortion over its entire working range. The operating frequency range of 25 Hz to 150 Hz complements other Meyer Sound loudspeakers in both straight and curved arrays for sound applications that require the greatest possible headroom at low frequencies.

The active 700-HP consists of two Meyer Sound ferrofluid-cooled 18-inch long-stroke drivers, each with a 4-inch voice coil with a compact neodymium magnet structure, in a specially adapted, ventilated housing. An integrated dual-channel Class AB / H amplifier with complementary MOSFET power amps delivers a maximum output of 2250 watts (1125 watts per channel).

The active 700-HP achieves a maximum output of 139 dB SPL within its working frequency range at 1 meter. The amplifier, control electronics and power supply are integrated in a separate interchangeable module, which is attached to the back of the box.

The 700-HP's efficiently tuned cabinet houses two Meyer Sound-designed and -manufactured back-vented, long-excursion, 18-inch cone drivers. Each driver has a 4-inch voice coil and is rated to handle 1200 AES watts. The drivers have also been engineered for extreme efficiency, using high-gauss neodymium magnets for the most powerful magnetic field strength. High magnetic field strength increases the driver's sensitivity, which yields greater output, while keeping heat dissipation requirements within operational tolerances.

An integral two-channel class AB/H amplifier with complementary MOSFET output stages supplies total peak power of 2250 watts (1125 watts per channel). With twice the amplifier power of the 650-P subwoofer, the 700-HP produces an average of 3 dB more overall SPL, with enormous headroom to accommodate the most extreme demands with ease. Recent tests conducted by Meyer Sound show the 700-HP producing significantly higher output than other "high-power" subwoofers.

The amplifier, control electronics and power supply are integrated into a single, field-replaceable module mounted in the rear of the cabinet. The cabinet is constructed of multi-ply hardwood and coated with a textured black finish. Integral metal grills lined with acoustical black mesh protect the cone drivers. Designed mainly for stage or ground placement, the stackable 700-HP includes plastic skids on the bottom of the unit, preventing damage to the enclosure or the unit below. The skids align with slots on the cabinet's upper surfaces ensuring secure, aligned stacking. For maximum convenience in touring situations, the 700-HP can even travel in stacks on the MCF-700 caster frame.

Features

  •  Stackable
  • Flyable using optional rigging kit
  • Extremely low distortion for ultimate low-frequency clarity
  • Very high peak power yields excellent transient reproduction
  • Transportable in blocks using optional heavy-duty caster frame
  • Exceptionally reliable and durable

700-HP Data

ACOUSTICAL

Operating Frequency Range

 

28 Hz – 150 Hz 

Frequency Response

 

0 Hz – 125 Hz &plusm;4 dB

Phase Response

 

45 Hz – 145 Hz &plusm;30°

Maximum Peak SPL

 

139 dB

Dynamic Range

 

> 110 dB

COVERAGE

 

 

360° (single unit); varies with number of units and configuration

TRANSDUCERS

Low/Low-Mid Frequency

 

Two 18″ cone drivers

Nominal impedance 4 Ω

 

Voice coil size 4"
Power-handling capability 1200 W (AES)4

AUDIO INPUT

Type

 

Differential, electronically balanced

Max. Common Mode Range

 

+/- 5V DC

Connectors

 

Female XLR input with male XLR loop output or VEAM all-in-one (integrates AC, audio and network)

Input Impedance

 

10 differential between pins 2 and 3

Wiring

 

Pin 1 Chassis/earth through 220 kO, 1000 pF, 15 V clamp network to provide virtual ground lift at audio frequencies
Pin 2 Signal (+)
Pin 3 Signal (-)

DC Blocking

 

Differential DC Blocking up to the maximum common mode voltage.

CMRR

 

> 50 dB, typically 80 dB (50 Hz - 500 Hz)

RF Filter

 

Common Mode 425 kHz
Differential Mode 142 kHz

TIM Filter

 

Integral to signal processing (<80 kHz)

Nominal Input Sensitivity

 

0 dB V (1 V rms, 1.4 V pk) continuous is typically the onset of limiting for noise and music.

Input Level

 

Audio source must be capable of producing +20 dBV (10 V rms, 14 V pk) into 600 Ohm in order to produce maximum peak SPL over the operating bandwidth of the loudspeaker

AMPLIFIERS

Amplifier Type

 

Two-channel complementary power MOSFET output stages (class AB/H)

Output Power

 

2250 W (1125 W/channel)5

THD, IM, TIM

 

<.02%

Load Capacity

 

4 Ω each channel

Cooling

 

Forced air cooling, two fans (one ultrahigh-speed reserve fan)

AC POWER

AC Connector

 

250 VAC NEMA L6-20 (twist lock), IEC 309 male inlet, or VEAM

Voltage Selection

 

Automatic, two ranges, each with high-low voltage tap

Safety Agency Related Voltage

 

95 VAC – 125 VAC, 208 VAC – 235 VAC; 50/60 Hz

Turn On/Off Points

 

85 VAC – 134 VAC; 165 VAC – 264 VAC; 50/60 Hz

CURRENT DRAW

   

Idle Current

 

0.640 A rms at 115 VAC; 0.320 A rms at 230 VAC; 0.850 A rms at 100 VAC

Max. Long Term Cont (>10 sec)

 

8.8 A rms at 115 VAC; 4 A rms at 230 VAC; 10 A rms at 100 VAC

Burst Current (<1 sec)

 

19 A rms at 115 VAC; 9.5 A rms at 230 VAC; 22 A rms at 100 VAC

Ultimate Short Term Peak

 

39 A pk at 115 VAC; 20 A pk at 230 VAC; 45 A pk at 100 VAC 

Inrush Current

 

7 A pk at 115 VAC; 7 A pk at 230 VAC; 10 A pk at 100 VAC

RMS NETWORK

   

Equipped with two-conductor twisted-pair network, reporting all operating parameters of amplifiers to system operator’s host computer.

PHYSICAL

Dimensions

 

45.93″”W x 22.50″”H x 30.00″”D (1167 x 572 x 762 mm)

Weight

 

204 lbs (92.53 kg)

Enclosure

 

Multi-ply hardwood

Finish

 

Black textured

Protective Grill

 

Perforated metal grille lined with acoustical black mesh

Quick Fly Rigging

 

Optional QuickFly® rigging kit available, with aluminum and steel side rigging bars, AlignaLinks and quick release pins

     

700-HP Schematic

meyer-sound-700-hp-schematic-shs-global-v4.png

Product Videos

Pickup Sound system Meyer 700HP Sub 01:04

Want to know what's in my toolbox? http://bit.ly/allainthebridsSHOP

  • Pickup Sound s...
    Want to know what's in my toolbox? http://bit.ly/allainthebrid...
  • Meyer Sound MI...
    Nepriklausomi Garso Rezisieriai 2015 Devil Stone PA: Meyer Sou...
  • 1100-LFC: The ...
    With the debut of the new 1100-LFC low-frequency control eleme...
  • Meyer Sound MI...
    Norah Jones was first supported by a Meyer Sound system in 200...
  • Meyer Sound LE...
    http://goo.gl/V6VrrO – Zur kompletten Reportage mit links zu d...
  • Lituanika 30 (...
    Nepriklausomi Garso Rezisieriai 2015 Lituanika 30 fetival PA: ...
  • DEMO Meyer Sou...
    en el montaje de el concierto de METALLICA
  • A wet Meyer So...
    Thanks to the landlord for leaving the roof without any tar or...

Other Details

Location:
North America & Europe
Warranty:
Limited warranty
Sales Questions?:

Find Similar Products by Category

Click the button below to add the Meyer Sound 700-HP Active Subwoofer to your wish list.