Site Information

 Loading... Please wait...

Meyer 8x M’elodie Package


Other Details

Included in price
Limited warranty
Sales Questions?:

Pre-owned M'elodie Array package in very good shape properly maintained and cared throughout the life of the package.

For inquiries contact



M'elodie  loudspeaker



Meyer Sound’s M’elodie, is best defined as a ultracompact loudspeaker with extraordinary power; the latest addition to the company’s MILO family of self-powered speakers. M’elodie shares the smooth, extended high-frequency response and easy-to-use rigging of the premium MILO family, but has a smaller footprint than the MICA compact array speaker. M’elodie brings the sonic signature and easy to use rigging of the MILO family of loudspeakers, along with an astonishing power-to-size ratio to a package smaller than the company’s MICA compact high-power curvilinear array loudspeaker. M’elodie provides a wide 100 degrees of horizontal coverage and produces maximum peak output levels up to 131dB SPL over its operating frequency range of 70Hz to 18kHz. Individual speakers measure approximately 29in x 9.5in x 13in weighing in at less than 65lb. As a result, M’elodie is compact enough for small theatres, ballrooms and clubs, as well as being an outstanding performer in theatrical productions and corporate AV applications. M’elodie provides a reliable, low-distortion solution for a key segment of the sound reinforcement market.


M’elodie is a two-way design. A pair of neodymium magnet 8in cone drivers cover the low/low-mid frequency range. An integral electronic crossover rolls off one driver at a lower frequency than the other in order to maintain optimal polar and frequency response through the crossover region. The high-frequency section uses a single 3in diaphragm compression driver (the same one used in MICA) for tight vertical coverage and coupled to a horn for constant horizontal directivity. M’elodie’s on-board power is supplied by a three-channel, class AB/H amplifier conservatively rated at 1200W total burst output (2400W peak).



  • Exceptional power-to-size ratio
  • Wide and even horizontal coverage pattern
  • Very small footprint keeps a low profile appearance
  • Seamless integration with MICA
  • QuickFly rigging with captive GuideALinks simplifies use in flown or groundstacked arrays, alone or with 500-HP, 600-HP subwoofers
  • Cardioid arrays when used in combination with 500-HP subwoofers

M’elodie DATA


Operating Frequency Range:


70 Hz - 18 kHz

Frequency Response:


76 Hz - 16 kHz (+/- 4dB)

Phase Response:


1.5 kHz - 16 kHz (+/- 30 degree)

Maximum Peak SPL:


131 dB

Dynamic Range:


> 110 dB







Varies, depending on array length and configuration




1100 Hz


Low/Low-Mid Frequency:


Two 8" cone drivers with neodymium magnets

Nominal impedance: 4 Ω

Voice coil size: 1.5"

Power handling capability: 600 W (AES); 900 W peak

High Frequency:


3" compression driver
Nominal impedance: 8 Ω
Voice coil size: 3"
Diaphragm size: 3"
Exit size: 1.2"

Power handling capability: 180 W (AES); 360 W peak




Differential, electronically balanced

Max. Common Mode Rejection:


+/- 5V DC



Female XLR input with male XLR loop output

Input Impedance:


10k Ohms differential between pins 2 and 3



Pin 1: Chassis/earth through 220 kO, 1000 pF, 15 V

clamp network to provide virtual ground lift at audio frequencies
Pin 2: Signal (+)
Pin 3: Signal (-)

DC Blocking:


Differntial DC Blocking up to the maximum common mode voltage.



> 50 dB, typically 80 dB (50 Hz - 500 Hz)

RF Filter:


Common Mode: 425 kHz
Differntial Mode: 142 kHz

TIM Filter:


Integral to signal processing (<80 kHz)

Nominal Input Sensitivity:


0 dB V (1 V rms, 1.4 V pk) continuous is typically the onset of limiting for noise and music.

Input Level:


Audio source must be capable of producing +20 dBV (10 V rms, 14 V pk) into 600 Ohm

in order to produce maximum peak SPL over the operating bandwidth of the loudspeaker


Amplifier Type:


Three-channel complementary MOSFET output stages (class AB/H)

Output Power:


1275 W (three channels; 2 x 500 W, 1 x 275 W);

Total Output:


2550 W peak



< .02%

Load Capacity:


4 Ohm low and mid; 8 Ohm high channel



Convection Cooled


AC Connector:


PowerCon with looping output or VEAM all-in-one connector (integrates AC, audio and network) 

Voltage Selection:


Automatic, two ranges, each with high-low voltage tap (uninterrupted)

Safety Agency Related Voltage:


95 V AC – 125 V AC, 208 V AC - 235 V AC, 50/60 Hz

Turn On/Off Points:


85 V AC - 134 V AC; 165 V AC - 264 V AC 




Idle Current:


.680 A rms (115 V AC), .360 A rms (230 V AC), .760 A rms (100 V AC)

Max. Long Term Cont (>10 sec):


2.3  A rms (115 V AC); 1.2 A rms (230 V AC); 2.6 A rms (100 V AC)

Burst Current (<1 sec):


4 A rms (115 V AC), 2 A rms (230 V AC), 4.5 A rms (100 V AC)

Ultimate Short Term Peak:


13 A pk (115 V AC), 6.5 A pk (230 V AC), 15 A pk (100 V AC)

Inrush Current:


10 A pk (115 and 100 V AC), 18 A pk (230 V AC)




Equipped with two-conductor twisted-pair network, reporting all

operating parameters of amplifiers to system operator’s host computer.




28.54 w x 9.19 h x 12.75 d (724.84 mm x 233.31 mm x 323.85 mm)



Weight 62 lbs (28.12 kg)



Premium Birch Plywood



Black textured

Protective Grill:


Powder-coated hex stamped steel with black mesh

Quick Fly Rigging:



Rigging and Accessories:


QuickFly rigging with four captive GuideALinks in the bottom corners of

two aluminum and steel end frames, secured with quick-release pins



Signal Flow for a Typical Reinforcement System

M'elodie loudspeakers permit versatile arrays and are compatible with other Meyer Sound reinforcement loudspeakers, giving sound designers maximum freedom to customize systems for their needs. This diagram illustrates the signal flow for a typical sound reinforcement system using 12 M'elodie cabinets per side for the main arrays.



Product Videos

Rigging Meyer M'elodie 01:44

Finalmente da Meyer il video di come si appende l'impianto, non che non lo sapessimo fare, ma per fare formazione va sempre bene. Grazie John

  • Rigging Meyer ...
    Finalmente da Meyer il video di come si appende l'impianto, no...
  • meyer sound m'...
  • ProLight + Sou...
  • meyer sound m'...
    è la dimostrazione dell'impianto line array m'elodie della mey...
  • meyer sound m'...
  • meyer sound m'...
  • meyer sound m'...
  • meyer m'elodie

Other Details

Included in price
Limited warranty
Sales Questions?:

Find Similar Products by Category

Click the button below to add the Meyer 8x M’elodie Package to your wish list.